This set features our new Double-Sided Water Stones that measure 8" x 2 3/4" x 7/8". It includes the 220/1000 and the 3000/8000 grit water stones, 12" Double-Sided Paddle Strop, Green Honing Compound, Stone Holder and the large 10" x 4" Double-Time Flattening Stone. The water stones are a perfectly matched set that is ideal for just about any sharpening project.
Set of 2 Double-Sided Water Stones
Fast Cutting and Hard Wearing
These are well-balanced stones. They emphasize fast-cutting action, some of the fastest we have seen. Yet they also keep their shape well, not requiring excessive resurfacing.
While the combination of fast cutting and hard-wearing sounds pretty straightforward, it's actually a trick to pull off. With sharpening stones, there is a delicate balance between the speed of cutting and the ability to hold flatness. The two features don’t always go hand-in-hand. Often, stones are fast, precisely because they break down quickly and expose fresh grit when used. Stones that don't break down as quickly on the other hand sacrifice some speed of cutting for the benefit of holding their shape longer. We're very pleased with how our Water Stones balance the two attributes.
Sharpening Supplies Water Stones are constructed with a vitrified bond rather than a resin bond. We find that this gives them a responsive feel in use. You can feel the cutting action while using these stones. They feel firm, not muddy or soft like some other water stones.
They are a soaking stone and do need to be placed in water for 10-20 minutes until saturated before use. However, unlike other stones that discourage storage in water, the bond of Sharpening Supplies Water Stones will not degrade with long term water contact giving you the option to store them in water if you prefer.
We designed the set so four grits would make a well-matched set. The 220 is an aggressive stone for dull edges. The 1000 grit is used after the 220 or as a starting point for only moderately dull edges. The 3000 grit is a fine stone and provides a very edge and prepares it for the final grit. The 8000 grit will put a polished edge on any tool or knife.
Each water stone measures 8" x 2-3/4" x 7/8". This size works well for tools and knives.
We believe in sourcing American-made products, so we're proud to say that our Water Stones are made right here in the USA.
Large 12" Double-Sided Leather Strop
The leather area on our 12" XL Paddle Strop measures 12" x 3" in size. The total length of the strop is over 16". Due to the large size and width, this strop is ideal for both tools and knives.
This 2 Sided Paddle Strop has 1 smooth side and 1 suede side.
Smooth - The smooth leather option is a very firm piece of leather. This leather is selected specifically for the smooth side only. If the leather is too hard, it just doesn't work well and doesn't accept the compound well. If the leather is too soft, it doesn't produce as fine of an edge and won't hold up. This leather is more durable than the softer leathers.
Suede - The suede side uses the opposite side of the leather (it is technically called the flesh side). The leather we use is selected for its flesh side properties. This leather is different leather than our smooth side leather. In our research, the leather that makes a good suede side is different than the leather that makes a good smooth side. Our suede leather is a little softer than the smooth leather. The suede leather accepts compound very readily.
Made with pride in the USA.
Green Honing Compound
This fine chromium oxide and aluminum oxide abrasive is used when you want a polished, honed edge on your tools, and it can be used on leather, wood or synthetic strops. The waxy consistency makes it easy to apply the compound. Simply rub the bar of compound on your strop. Think of the compound as a big crayon and apply it evenly to your surface. There is no need to apply too aggressively, you don't need much to be effective. After you've applied some compound, your strop will now polish your blade edges more quickly and will help you achieve a mirror polish.
6 oz. bar. Made in the USA.
Double-Time Flattening Stone
When our flattening stone is made, care is taken to ensure that it comes out of the mold flat. That flatness is critical because that is what determines how flat you can make your stone. We take two additional steps when ours are made. First, each stone is hand lapped to ensure flatness. It takes time to do it, but that is the only way to make it flatter. Second, each stone is precisely measured to ensure flatness. If it doesn't pass the test, it is sent back for additional lapping.
Flattening Stone Size Matters
The size of the flattening stone matters for a few reasons. The larger stone is easier to use as your water stone stays on the surface. But total wear is another benefit. Our large (10" x 4") double-sided stone has 80 square inches of total flattening surface. That is almost 3 times the wearable area of other popular flattening stones.
Seeing the Double-Time Flattening Stone next to other popular flattening stones shows the size difference. And, it's double-sided!
Hard Abrasive Materials
We chose green silicon carbide as our abrasive material for our flattening stone because it is extremely hard and the particle shape cuts aggressively. It is harder than aluminum oxide, and also harder than the less expensive black silicon carbide. This makes it ideal for flattening as it cuts quicker and wears slower.
Two Sides for Fast Flattening and Smooth Surfaces
Just like with sharpening an edge, the coarser the grit, the faster the cutting action. However, the coarser the grit, the coarser the surface it will leave. We experimented with different grits to find the best overall option. We wanted to find a better solution to that compromise. Our solution was to make it double-sided. Something we have not seen on any other flattening stone before.
The coarse side is a very fast cutting 120 grit. Especially when working on coarse water stones, this side provides the necessary cutting action to effectively flatten the stone. However, when flattening finer stones, a coarse grit leaves a finish that many find undesirable. That is why we put a 320 grit surface on the fine side. On water stones 1000 grit and higher, we recommend using the fine side to put a nice surface finish on the stone. The fine side can even be used alone on very fine water stones to put a fresh flat surface on your stone.
In addition, the distinctive grid pattern of the grooves clears waste material quickly and efficiently, aiding the fast cutting action on both sides of the Double-Time Flattening Stone.
Made In the USA
We've supported US manufacturing since we started and that continues to be important to us. When we set out to create our new flattening stone, we knew we could make a great flattening stone in the US. We feel that everyone benefits when quality products are made in the USA. We're not only supporting the economy, but we are producing a product with a quality that everyone can appreciate.
100% Satisfaction Guarantee
We're so confident that you'll like the Double-Time Flattening Stone that we're backing it up with a 100% satisfaction guarantee. If you're not happy with any aspect of the stone, just let us know and we'll gladly replace or refund your purchase.
Our stone holder works well with our water stones. The rubber feet keep the stone from sliding around and have the added benefit of raising the stone 7/8" above the work surface, just enough to easily make room for your hands while sharpening. The sturdy chrome-plated steel rails are corrosion resistant.